FDXLHXA1250 Hayward H-Series H250FD Heater Heat Exchanger

$870.99 in Store

$897.99

5.00 out of 5 based on 3 customer ratings
FREE SHIPPING!
Ships in 24 Hours, If In Stock

Out of stock

Online Inventory is Accurate, No Need to Confirm.

Condition - NEW

Item ID # 16137

Get Notified Once Back In Stock

SKU: FDXLHXA1250 Categories
,
GTIN: 610377073738
Description

Heat Exchanger Assembly for Hayward H250FD Universal H-Series Low Nox Pool Heater FDXLHXA1250

Heat Exchanger Replacement Procedure

Heat Exchanger Service Parts Kits for Universal H-Series (Forced-Draft) Heaters

IMPORTANT NOTES:

REPLACEMENT PROCEDURE

  1. This kit is intended to be used only with Hayward Universal H-Series (forced-draft) gas heater models.
    These heaters may be identified by inspection of the heater rating plate (there should be an “FD” in the model number), or by visual inspection of the heater in comparison to the
    diagrams in these instructions.
  2. This instruction sheet is intended for the following heater
    service parts kits:

FDXLHXA1250 Heat Exchanger Assembly, H250FD
FDXLHXA1350 Heat Exchanger Assembly, H350FD
FDXLHXA1400 Heat Exchanger Assembly, H400FD

  1. Tum pump, main as valve, and heater power off.
  2. Remove drain plug and drain water out of heat exchanger.
  3. If necessary, disconnect header union fittings from pool/spa piping.
  4. Pull temperature limit switch wires through the grommet on the heater side panel. and disconnect limit switch wires from heater wire harness.
  5. Remove screws and remove both of the upper plastic heater side panels (see Figure 1 for screw locations, and Figure 2 for part locationhdentification).
  6. Disconnect the 2 wires from the pressure switch. which is located on the inletloutlet header.
  7. Remove countersunk screws on heater top and  remove louvered exhaust panel on heater top (see Figure 2).
  8. Remove the heater top tlue cover by removing 3 screws on each side of the heater (see Figure 2).
  9. Remove screws and remove rain shield assembly (see Figure 2). Note that there are screws which hold the
    rain shield assembly to the heat exchanger tube sheets, which also must be removed.
  10. Remove the front access panel and the control box cover (see Figure 2).
  11. Disconnect the temperature sensor plug from the circuit board located inside the control box.
  12. Pull the temperature sensor wires out of the control box and through the hole in the heater cabinet.
  13. Carefully lift the heat exchanger up and out of the heater cabinet.
  14. Before installing the new heat exchanger assembly, install the new adhesive-backed gaskets (included in this kit) onto both ,of the new heat exchanger tubesheets.
  15. Install the new heat exchanger assembly. Ensure the heat exchanger is properly oriented with the arrows on the tube sheet decal pointing up.
    CAUTION: Do not install heat exchanger upside down. Heat exchanger is labeled to indicate the
    proper orientation. The heat exchanger will be damaged if installed incorrectly.
  16. Remove the pressure switch from the old heat exchanger assembly and install on the new heat exchanger assembly. Apply pipe thread sealant to the pressure switch threads before assembly.
  17. Reverse the above steps to reassemble the heater.
  18. Activate water pump and check the system for leaks.

Hayward FD400 Heater Heat Exchanger FDXLHXA1400

Reviews (3)

3 reviews for FDXLHXA1250 Hayward H-Series H250FD Heater Heat Exchanger

  1. blank

    Roy S.

    Pleased with the transaction

  2. blank

    Chris

    Arrived in time, brand new, original

  3. blank

    Kelly F.

    Pleased with the transaction

Add a review

Your email address will not be published. Required fields are marked *

Email us about the item
Why Choose Best Pool Shop?

Best Pool Shop offers expert advice, top-quality products, and free shipping on many items. We’re committed to providing the best pool equipment and supplies to make your pool experience seamless and enjoyable.Choosing Best Pool Shop comes with several advantages, especially for pool owners and enthusiasts looking for quality, reliability, and convenience. Here’s why Best Pool Shop stands out:

  • Wide selection of pool equipment and supplies:
    Whether it's pool equipment, maintenance supplies, or accessories, Best Pool Shop carries a wide variety of top brands, including Pentair, Jandy, Hayward and more
  • Competitive pricing:
    At Best Pool Shop we do oure best so that customers get the best deals without compromising on quality. We also offer promotions and discounts to keep pool maintenance affordable.
  • Expert customer support:
  • With years of experience in the pool industry, Best Pool Shop offers expert advice and in-depth product knowledge to help customers make the best decisions for their pool needs.
  • Free & Fast shipping on many products:
  • The shop offers free shipping on many products, making it more convenient for customers across the U.S. to receive their purchases quickly and affordably.
  • Customer-Centric Return Policy:
    Best Pool Shop has clear policies that prioritize transparency, ensuring customers understand their rights and what to expect from the shopping experience.
  • Reputation for Reliability:
    With a commitment to customer satisfaction and consistent support, Best Pool Shop is a trusted name in the pool equipment industry.

These points showcase why Best Pool Shop is the go-to choice for pool owners who want top-tier products and reliable service.

Skip to content