Sale!

FDXLIGN1930 GENUINE Hayward H-Series FD Heater Hot Surface Ignitor 768A-008 1501643901

$72.99 in Store

Original price was: $82.87.Current price is: $73.99.

Product ID: 3445

FREE STANDARD SHIPPING
3 DAY SHIPPING FOR ONLY $9.99
Ships in 1 Business Day from Los Angeles

Brand New Product

(2 customer reviews)

Only 14 left in stock

Add to Cart
Hayward H-Series FD Heater Hot Surface Ignitor FDXLIGN1930
FDXLIGN1930 GENUINE Hayward H-Series FD Heater Hot Surface Ignitor 768A-008 1501643901
$82.87 Original price was: $82.87.$73.99Current price is: $73.99.
Hurry, this item is selling fast!

Original Authentic Hayward Hot Surface Ignitor for Hayward Universal H-Series Low Nox Pool Heater 768A-008 1501643901 FDXLIGN1930

Ignitor Replacement Procedure.
FDXLIGN1930
for Universal H-Series (Forced-Draft) Heaters

  • Fits hayward universal H-series low nox pool heater models h150fdn, h150fdp, h200fdn, h200fdp, h250fdn, h250fdp
  • Also fits hayward universal h-series low nox pool heater models h300fdn, h300fdp, h350fdn, h350fdp, h400fdn, h400fdp

IMPORTANT NOTES:

This kit. is intended to be used only with Hayward Universal H-Series (forced-draft) gas heater models. These heaters may be identified by inspection of the heater rating plate (there should be an FD’ in the model number), or by visual inspection of the heater in comparison to the diagrams in these instructions.

REPLACEMENT PROCEDURE

  1. Turn pump, main gas valve, and heater power off.
  2. Loosen 4 screws on front access door and remove front access door.
  3. Remove screws and remove control box cover.
  4. Disconnect the ignitor plug from the large circuit board located inside the control box.
  5. Remove screw and move ignitor access cover to allow access to the ignitor. Note the cover remains connected to the ignitor wires.
  6. Remove 2 screws and remove the old ignitor from heater front combustion chamber panel.
  7. Separate the old black plastic strain relief from the ignitor access cover by compressing the tabs using a pair of pliers.
  8. Istall new ignitor to heater front combustion chamber panel with 2 screws.
  9. Route new ignitor wires through hole in ignitor access cover and install ignitor access cover ln heater with 1 screw. Note the tab in the back of the ignitor access cover must go into the slot ln the heater.
  10. Snap the new plastic strain relief over the ignitor wires immediately above the hole in the ignitor access cover. Once the new plastic strain relief is snapped onto the ignitor wires, press it into the hole In the ignitor access cover. Minimize the slack in the ignitor wires by refulty pulling excess slack up through the strain relief.
  11. Route the ignitor wires through the heater and into the control box. Plug the end of the ignitor wires into the large circuit board to the connector labeled lGNlTOR. Ensure the ignitor wires are routed such that they do not come in contact with moving parts on the blower. Re-install control box cover and heater front access
    door.
  12. Turn on pump, main gas valve, and heater power: and activate heater to test the new ignitor.

Hot surace ignitors are fragile. Handle with care.

RISK OF ELECTRIC SHOCK
Disconnect electrical power from heater before servicing. Failure to disconnect power
may result in injury or death

FDXLIGN1930 service & installation manual

2 reviews for FDXLIGN1930 GENUINE Hayward H-Series FD Heater Hot Surface Ignitor 768A-008 1501643901

  1. blank

    Alice F.

    Super!

  2. blank

    Linda Y.

    Super!

Add a review

Your email address will not be published. Required fields are marked *

Additional information

Weight 3.00 lbs
Manufacturer

Hayward